Toyota |
Model/Engine Type | Type | F/W (kgs.) | Assy (kgs.) |
| Supra JZA70 | TS2B | 6.80 | 13.20 |
| 1JZ-GTE | TS2BD | 7.00 | 14.15 |
| 　 | TS2CD | 7.30 | 14.90 |
| 　 | TR2CD | 7.30 | 15.45 |
| 　 | TS3BW | 9.70 | 17.75 |
| 　 | R3C | 5.00 | 11.00 |
| 　 | R4C | 5.40 | 16.65 |
| *OS Clutch Release Movement Alteration Kit is required for installation | 5.00 | 11.00 |
| Â | Â | Â | Â |
| Supra JZA80 | TS2CD | 5.10 | 11.10 |
| 2JZ-GTE | TR2CD | 6.80 | 14.95 |
| *Sleeve Bearing is included in all above models | TS3B | 6.40 | 14.45 |
| 　 | TS3BW | 9.65 | 17.70 |
| 　 | R3C | 6.10 | 15.75 |
| 　 | R4C | 5.40 | 16.65 |
| *OS Clutch Release Movement Alteration Kit is required for installation | 　 | 　 |
| Optional Parts: *Flywheel bolt set, and Clutch disk center alignment tool | 　 | 　 |
| Â | Â | Â | Â |
| Supra MA70 | TS2B | 6.10 | 12.50 |
| 7M-GTE | TS2BD | 6.70 | 13.85 |
| 　 | TS2CD | 7.00 | 14.60 |
| 　 | TR2CD | 7.00 | 15.15 |
| 　 | TS3B | 6.10 | 14.15 |
| 　 | TS3BW | 8.85 | 16.90 |
| *OS Clutch Release Movement Alteration Kit is required for installation | 　 | 　 |
| Â | Â | Â | Â |
| Supra & Soarer | TS2B | 5.80 | 13.95 |
| 3S-G | 　 | 　 | 　 |
| *This clutch set is thinner than the orginal equipped clutch system. Adjustment of the clearance by spacer | 　 | 　 |
| (about 3mm in thickness) between release sleeve and sleeve bearing may be needed. | 　 | 　 |
| Â | Â | Â | Â |
| Soarer GZ20, Mark II GX71, Chaser GX81 | TS2B | 5.50 | 11.90 |
| 1G-GT | 　 | 　 | 　 |
| *This clutch set is thinner than the orginal equipped clutch system. Adjustment of the clearance by spacer | 　 | 　 |
| (about 3mm in thickness) between release sleeve and sleeve bearing may be needed. | 　 | 　 |
| Optional Sleeve Bearing Set to adjust thickness | 　 | 　 |
| Â | Â | Â | Â |
| Altezza SXE10 | TS2BD | 5.80 | 13.95 |
| 3SG | 　 | 　 | 　 |
| *OS Sleeve Bearing Set and 8 Genuine Nissan Flywheel bolts (pn:1231504U100) are needed for | 　 | 　 |
| installation of above clutch. | 　 | 　 |
| Â | Â | Â | Â |
| MR2 SW20 | TS2B | 5.90 | 12.30 |
| 3SGT | 　 | 　 | 　 |
| *OS Sleeve Bearing set is needed to install the above clutch. | 　 | 　 |
| Â | Â | Â | Â |
| MR2 SW20 (NA) | TS2B | 　 | 　 |
| 3SG | 　 | 　 | 　 |
| *OS Sleeve Bearing set is needed to install the above clutch. | 　 | 　 |
| Â | Â | Â | Â |
| Celica ST185, ST205 | TS2B | 4.50 | 12.30 |
| 3SGT | R2CD | 4.50 | 12.90 |
| *OS Sleeve Bearing set is needed to install the above clutch. | 　 | 　 |
| Â | Â | Â | Â |
| Celica ST202 (NA) | TS2B | 　 | 　 |
| 3SG | R2CD | 　 | 　 |
| *OS Sleeve Bearing set is needed to install the above clutch. | 　 | 　 |
| *Super Strut Viscous LSD equipped models should use same clutch as Turbo charged models. | 　 | 　 |
| Â | Â | Â | Â |
| Levin, Trueno AE86, AE92, AE101 | TS2AS | 3.60 | 8.30 |
| 4A-G | TS2A | 3.60 | 8.70 |
| 　 | TS2BS | 5.05 | 10.95 |
| 　 | TS2B | 5.05 | 11.45 |
| *When used for AE86, any of these clutch systems are thinner than the orginal equipped clutch system. | 　 | 　 |
| Adjustment of the clearance by spacer (about 3mm in thickness) between release sleeve and sleeve bearing | 　 | 　 |
| may be needed. | 　 | 　 |
| Â | Â | Â | Â |
| Levin, Trueno AE92, AE101 | TS2A | 3.60 | 8.70 |
| 4A-GZ | TS2B | 5.05 | 11.45 |
| 　 | 　 | 　 | 　 |
| Starlet EP82 | TS2A | 4.65 | 9.75 |
| 4E | TS2B | 4.30 | 10.70 |